Blueberry: Handmade 1/12 Scale Miniature Push Mold for Clay, Flexible Silicone Molds, Deco Parts, Fake Sweets, HUEPROJECT

Sold by HUEPROJECTcom
(5)
$6.60
+ $21.00 shipping
$6.60
+ $21.00 shipping
Made to order
Preparation takes 3-5 business days
Arrives from South Korea

Features
Handmade

Item details

Hand made silicone molds
by HUEPROJECT(http://hueproject.com) in South Korea.



▼ All About Hue Project’s Molds!

1. Manual work
Hue Project’s molds are all manufactured through manual work one by one starting from prototype design and manufacturing to defoamation, finishing, and packaging.

2. Best Quality Materials
As it is manufactured with elastic and flexible high-strength and high-quality silicone (Dowcorning 3481 Silicone), it corresponds to various clays, plaster, urethane, and candle wax. (If you are using a gel for nail art that can be hardened only if exposed to LED or direct rays, use our Clear Mold.) As it is also very strong to heat, it can withstand up to 220℃ in an oven specialized for clay and so you can use materials that diffuse heat strongly. But, if you use materials similar to molds, for example, silicone and sealant, separate mold releasing agents are required.

3. Mold Size
2.5cm x 2.5cm

4.Management and Storage
Wash contaminated molds lightly with running water. After use, if you keep it clean and dry, it can be used semipermanently.

5. Notes
The copyright of Hue Project’s molds is solely on Hue Project. Illegal reproduction will be reported to the police without monition as soon as it is exposed.




▼How to Use Mold

1. Prepare materials to inject into a silicone mold.
Be sure to check mold to see if there are any dusts inside and outside of the mold. Nitrile gloves are recommended to avoid dusts in the materials to inject. Mold releasing agents are required depending on the characteristics of the materials to inject.

2. Inject materials into a mold.
In injecting materials to a mold, be careful not to produce foams at the corner of mold.
In case of liquid materials like resin, use toothpick or needle to pop the bubbles as much as possible.
In case of solid materials with high viscosity like clay, inject them pressing strongly from the top so that materials can be penetrated into every corner of mold.
If there are foams or spaces between the mold and the materials before they are hardened, it may cause defects in finished goods.

3.Harden/dehydrate materials.
In case of the materials that must be hardened in liquid state, do not extract them by force from the mold until completely hardened.
In case of the materials that must be dehydrated after being exposed to air, extract them from the mold and then dehydrate.
As the hardening/dehydrating method depends on materials, be well-informed of the characteristics of materials and how to use them before injecting them into a mold!

4. Polish finished parts.
Remove fragments and mold traces formed at the edge of hardened/dehydrated parts with sandpaper or graver. If parts are well-trimmed, coat as desired or use as they are!
With these molds and materials, you can make parts easily at home alone!




▼ Lead Time

Hue Project’s all products will be delivered within 7 days at least due to manual work. But, if there is an inventory, products ordered will be delivered the next day after order and payment are confirmed.




▼Guidance to Overseas Delivery

Hue Project’s all products can be delivered overseas.
For a faster and safe delivery, we are using post office’s official EMS (Expedited Mail Service).
The shipping charge is based on post office’s EMS universal overseas shipping schedule.




▼Legal notification

All of the copyrights of products of Hue Project are getting legal protection and in case duplication is made without authorization, it is applicable for punishment without any prior warning so please take caution of this.




All images, ideas, designs and content © HUEPROJECT. All rights reserved.


Reviews
Average review
(5)
Pas une grande ressemblance avec le fruit ... dommage
Jan 23, 2018 by Pat
Translate to English
Good supplier. I will buy again! Good quality.
Nov 8, 2017 by Ricissimas Welt
I love these molds thank you
Aug 1, 2016 by gabydicarlo
I love this mold. Just a tip, pre-bake just a few minutes IN the mold then pop them out, you can kind of still mold them so the top won't be flat, without totally ruining the details.
May 30, 2016 by Monique Kordasiewicz
Great quality items, service and packaging :)
Apr 26, 2016 by Rachel Lee

Shipping & policies
Preparation takes 3-5 business days
Arrives from South Korea
Estimated Shipping
Shipping to
Zip or postal code