Pres-N-Snap with Durable Dies / # 1 Grommet Die Set
Presenting the versatile and easy to use Pres-N-Snap. It is capable of setting numerous brands of fasteners simply by changing the dies. Its heat-treated cast-aluminum body makes it both lightweight and durable
The patented Pres-N-Snap hand tool ensures you years of troublefree service.
bullet The Pres-N-Snap and all its components are manufactured in the USA.
pns.jpg (17471 bytes)
The Press-N Snap tool comes with six dies for standard snaps ( Caps, Sockets, Studs, and Eyelets ) and #1 plain grommet installation. The Hoover Press N Snap is a durable and professional grade portable fastener installation tool that could save you hours of time on your next project. You can take it out to the project without having to take the project apart and bring it to the table. There is also a bench mounting bracket available to mount it to a table if you want to. (Sold separately )
Press-N-Snap Installation Tool Includes :Button Snap Die :Socket Die :Stud Die :Eyelett Die :#1 Plain Washer Grommet Dies
FOR THE PRES-N-SNAP
FIRST MAKE SURE THAT YOU HAVE THE CORRECT DIES FOR THE BRAND OF FASTENERS THAT YOU ARE USING.
REMOVING AND INSTALLING DIES ON THE PRES-N-SNAP IS ACCOMPLISHED BY PULLING THE DIES OFF OF THE TOOL, OR PUSHING THE DIES ONTO THE TOOL. IT HELPS TO ROTATE/TWIST THE DIES DURING INSTALLING AND THE REMOVAL OF DIES. ALL DIES ARE HELD ONTO THE TOOL BY BLACK "0" RINGS.
WITH THE HANDLE CLOSED, ADJUST THE END BOLT UNTIL THE DIES COME IN CONTACT,THEN BACK-OFF 1/2 TURN. PLACE THE FASTENERS INTO THEIR CORRESPONDING DIES.
LOCATE A PIECE OF SCRAP FABRIC AND FOLD TO THE SAME THICKNESS AS YOUR PROJECT. PLACE THE FABRIC BETWEEN THE DIES AND PRESS/SQUEEZE THE HANDLE. FASTENERS SHOULD NOT ROTATE WHEN SET IN FABRIC. CAUTION: OVERTIGHTENING MAY CAUSE DISTORTION TO THE FASTENERS AND CAN DAMAGE THE DIES.
IN THE EVENT THAT THE FASTENER ROTATES YOU MAY ADJUST THE END BOLT CLOCKWISE ON THE PRES-N-SNAP. REMOVE THE M-2700 GRAY RING TO PREVENT CUTTING IT. THEN CAREFULLY PRESS/SQUEEZE THE HANDLE BEING CERTAIN THAT THE FASTENER IS IN POSITION.
FOR INSTALLING GROMMETS USE THE SAME PROCESS AS FOR INSTALLING FASTENERS.
IF YOU ARE USING A STANDARD OR SPUR GROMMET YOU WILL NEED TO CUT/PIERCE A HOLE THROUGH ALL LAYERS OF MATERIAL AT ONE TIME. PLACE THE GROMMET THROUGH THE HOLE AND THE WASHER ON IT. WHILE HOLDING IT IN ONE HAND USE THE OTHER HAND TO POSITION THE PRES-N-SNAP AND PRESS/SQUEEZE THE HANDLE. THE GROMMET SITS ON THE ANVIL PORTION OF THE DIE SET AND THE WASHER SITS ON THE ROLLING PORTION. IF YOU ARE NOT SURE WHICH IS THE ANVIL AND ROLLING PORTION, PLEASE GO TO OUR PRES-N-SNAP DIES PAGE TO VIEW.
IF YOU HAVE SELF-PIERCING GROMMET DIES DO NOT WASTE TIME CUTTING/PIERCING A HOLE IN THE FABRIC. THE GROMMET AND GROMMET DIE WILL CUT AND ROLL IN ONE ACTION SAVING YOU TIME AND MONEY. WHEN PLACING THE GROMMET AND WASHER IN THE DIES, IT HELPS TO PLACE THE WASHER FIRST THEN THE GROMMET.
HAMMER HAND TOOLS
WHEN USING PUNCH TOOLS ALWAYS WHERE SAFETY GLASSES.
ALWAYS HAMMER INTO THE END GRAIN OF A SOLID PIECE OF WOOD, NEVER INTO THE SIDE OF THE WOOD FOR IT WOULD JAM WOOD INTO THE CUTTING PUNCH AND CAUSE DAMAGE TO YOUR TOOL.
Thank you so much for the fast shipping and quality product. I look forward to shopping with you again.